Processing steps for making CNC brass turning parts

Views: 0     Author: Site Editor     Publish Time: 2022-01-17      Origin: Site

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button
Processing steps for making CNC brass turning parts

The process of machining CNC brass turning parts is divided into three stages, and each stage has specific precautions. Only by clarifying the specific process of these three stages of machining CNC brass turning parts, can we safely produce high-quality brass Turned parts

Here is the content list:

l Before operation

l In operation

l After operation

Before operation

1 Strictly use protective equipment as required before work, tie the cuffs, no scarves or gloves, and female workers should put their defenses in their hats. The operator must stand on the pedals of the machine tool for the brass-turned parts.

2 Strictly check each part of the bolts, stroke limit, signal, safety protection (safety) device, mechanical transmission part, electrical part, and each lubrication point, and start it only after the reliability is confirmed.

3 The safety voltage applied to the lighting of various types of CNC brass turning parts for machine tools shall not exceed 36 volts.

In operation

1 The work, clamp, tool, and workpiece must be clamped firmly. All kinds of CNC brass turning parts of the machine tool should be idling at low speed after starting up. After everything is normal, it can be officially operated.

2 It is forbidden to put tools and other things on the track surface of the machine tool and the workbench of the CNC brass turning parts. It is not allowed to remove iron filings by hand, and special tools should be used to clean them.

3 Before starting the machine tool for CNC brass turning parts, observe the surrounding dynamics. After the machine tool is started, stand in a safe position to avoid the movement of CNC brass turning parts and the splashing of iron filings.

4 During the operation of the CNC brass turning parts machine tool, it is not allowed to adjust the speed change mechanism or stroke, and not to touch the transmission part, the CNC brass turning parts in motion, the cutting tool, etc. working surfaces in the process of processing, and it is not allowed to measure any size during operation. , It is forbidden to pass or take tools and other items through the transmission part of the machine tool.

5 If any abnormal noise is found, the machine should be stopped for maintenance immediately, and it is not allowed to run forcibly or with the disease, and the machine tool is not allowed to be overloaded.

6 During the processing of CNC brass turning parts, strictly implement the process discipline, read the drawings, see the control points, the roughness of each part, and the technical requirements of the relevant parts, and determine the processing procedures of the manufactured parts.

7 Stop the machine when adjusting the speed and stroke of the machine tool, clamping CNC brass turning parts and tools, and wiping the machine tool. It is forbidden to leave the work post when the CNC brass turning parts machine is running. If you want to leave for some reason, you must stop and cut off the power.

After operation

1 The raw materials of the CNC brass turning parts to be processed and the finished CNC brass turning parts, semi-finished products, and waste materials must be stacked in the designated place, and various tools and knives must be kept intact and good.

2 After the operation, you must cut off the power supply, remove the tool, put the handles in the neutral position, and lock the switch box.

3 The cleaning equipment is hygienic, the iron filings are cleaned, and the guide rails are filled with lubricating oil to prevent corrosion.

The customized CNC brass turning parts are fittings, which were made for Parker and were used in the field of hydraulics & pneumatics. The material is brass C3604, and the thread is 3/8-16. For the precision CNC brass turning parts, MOQ is 5000 PCS and the lead time is 30 days. JST is an OEM manufacturer, we can manufacture these CNC brass turning parts according to your drawings. If there are any projects with customized precision CNC turning brass parts or customized CNC brass turning parts and CNC Turning Parts , please do feel free to contact us for a quotation.



Kunshan JST Industry Co., Ltd is a professional manufacturer of CNC machining parts, which were applied to the field of medical, aerospace & aviation, electronics, security & safety, industrial equipment and automotive.

Copyright © 2020 Kunshan JST Industry Co., Ltd

CONTACT US

   86-18915758793

   86-512-55260690

   info@jstindustry.com

   info_282418

   Carrolgu

   86-18915758793

 

PRODUCTS

GET IN TOUCH